2025

Journalartikel

• Bödeker, F., Biel, A., Moshfegh, R. & Marzi, S. (2025). A novel FFT-based micromechanical modeling approach for the fracture behavior of a composite core in metal sandwich plates using a cohesive zone model. 10.1016/j.compstruct.2025.119231
• Neufeld, D., Geisel, L. & Marzi, S. (2025). A modified four-point-bend end-notched flexure test to study mixed-mode II+III fracture of adhesive joints. 10.1016/j.engfracmech.2025.111476
• Efferz, L., Dix, S., Schuler, C. & Kolling, S. (2025). Optical anisotropy effects in laminated tempered glass. 10.1007/s40940-024-00285-w
• Schmandt, C. & Marzi, S. (2025). A strain-rate-dependent cohesive zone model for peel-loaded thick and flexible adhesive layers of various geometries prone to stick–slip failure. 10.1016/j.tafmec.2024.104755

Konferenzpaper

• Aydin, L. & Marzi, S. (2025). Obtaining traction-separation laws of adhesive joints using optical fiber strain measurements - Part A (Mode I). 10.1016/j.prostr.2025.06.199
• Geisel, L. D. & Marzi, S. (2025). Obtaining traction-separation laws of adhesive joints using optical fiber strain measurements - Part B (Mode III). 10.1016/j.prostr.2025.06.198
• Kididane, I., Kozáková, K. & Marzi, S. (2025). Dual-actuator mixed-mode bending tests on adhesive joints of different thickness. 10.1016/j.prostr.2025.06.066
• Sirbu, I., Manthei, G., Guckert, M. & Bulut, E-B. (2025). Lokalisierung von Schallemissionsereignissen mittels künstlicher neuronaler Netze zur Bestimmung der Quellenkoordinaten. 10.58286/30955
• Bulut, E-B., Manthei, G., Sirbu, I. & Guckert, M. (2025). Anwendung künstlicher Intelligenz zur Quellenlokalisierung von Schallemissionsereignissen durch Untersuchung charakteristischer Signalmerkmale. 10.58286/30957

2024

Journalartikel

• Shamchi, S., Farahani, B. V., Bulla, M. & Kolling, S. (2024). Mechanical Behavior of Lithium-Ion Battery Separators under Uniaxial and Biaxial Loading Conditions. 10.3390/polym16081174
• Kididane, I., Ladwig, N. & Marzi, S. (2024). Dual-actuator mixed-mode bending tests on structural adhesive joints. 10.1016/j.engfracmech.2024.110017
• Bödeker, F., Herr, P., Biel, A., Moshfegh, R. & Marzi, S. (2024). An FFT-based homogenization scheme for cohesive zones with an application to adhesives and the core material of thin metal sandwich plates. 10.1016/j.tafmec.2023.104186
• Geisel, L. D. & Marzi, S. (2024). A modified single-leg bending test to study mode III fracture of adhesive joints. 10.1016/j.engfracmech.2024.110355
• Steckel, S. & Lademann, F. (2024). Implementierung von Photovoltaik auf Bahnsteigdächern.

Konferenzpaper

• Straub, T., Guckert, M., Fiedler, U. & Strauch, S. (2024). Explainable AI based Predictions for Workpiece Quality. 10.58286/30246
• Sirbu, I., Manthei, G., Guckert, M. & Bulut, E-B. (2024). Classification of Crack Coordinates through Wavelet - Analysis and CNN: Analysis of Data Preparation and Network Structure. 10.58286/30272
• Bulut, E-B., Manthei, G., Sirbu, I. & Guckert, M. (2024). Research of Acoustic Emission Characteristics and Applicability of Artificial Intelligence for Source Localization. 10.58286/30243

2023

Journalartikel

• Brokmann, C., Alter, C. & Kolling, S. (2023). A Methodology for Stochastic Simulation of Head Impact on Windshields. 10.3390/applmech4010010
• Van Roo, T., Kolling, S. & Dillenberger, F. (2023). On the Generation of Highly Oriented Test Specimens and the Influence of Preparation. https://amp.iaamonline.org/article_23889.html
• Schrader, P., Schmidt, A., Schlenz, M. A., Kolling, S., Wöstmann, B. & Berlinger, M. (2023). A statistical model of the rate-dependent fracture behavior of dental polymer-based biomaterials. 10.4012/dmj.2022-163
• Marzi, S. (2023). Experimental determination of coupled cohesive laws with an unsymmetrical stiffness matrix for structural adhesive joints loaded in mixed-mode I+III. 10.1016/j.engfracmech.2023.109215
• Schrader, P. & Marzi, S. (2023). Novel mode III DCB test setups and related evaluation methods to investigate the fracture behaviour of adhesive joints. 10.1016/j.tafmec.2022.103699
• Schrader, P., Domladovac, D. & Marzi, S. (2023). Influence of Loading Rate on the Cohesive Traction for Soft, Rubber-Like Adhesive Layers Loaded in Modes I and III. 10.3390/pr11020356

Konferenzpaper

• Kern, A., Wörner, S., Beier, H. T. & Jung, U. (2023). Bruchmechanische Lebensdauer-Prognose für additive gefertigte Aluminium Komponenten. 10.48447/BR-2023-007
• Kern, A., Hemmelmann, O. & Jung, U. (2023). Additive Fertigung vs. Guss: Ein Vergleich am Beispiel von Aluminium. 10.48447/ADD-2023-302
• Bulla, M., Sahraei, E. & Kolling, S. (2023). An Experimental and Computational Study of Mechanically and Dynamically High Loaded Separators for Lithium-Ion Batteries. 10.1115/IMECE2023-112272

Sammelbandbeitrag

• Bark, A. (2023). Planungsvorgaben im Technischen Regelwerk zur Erhöhung der Verkehrssicherheit von Landstraßen. https://vod-ev.org/vod-schriftenreihe-nr-2-vision-zero-konkret/
• Marzi, S. (2023). 16 - Innovations in fracture testing of structural adhesive bonds. 10.1016/B978-0-323-91214-3.00006-5

2022

Journalartikel

• Loh, L. & Marzi, S. (2022). Corrigendum to “A novel experimental methodology to identify fracture envelopes and cohesive laws in mixed-mode I+III” [Eng. Fract. Mech. 214 (2019), 304–319]. 10.1016/j.engfracmech.2022.108294
• Abdelkader, A., Moos, C., Pellou, A., Pfeiffer, M., Alter, C., Kolling, S. & Keck, C. M. (2022). Tablets Made from Paper - An Industrially Feasible Approach. 10.3390/ph15101188
• Dix, S., Schuler, C. & Kolling, S. (2022). Digital full-field photoelasticity of tempered architectural glass. 10.1016/j.optlaseng.2022.106998
• Dix, S., Efferz, L., Hiss, S., Schuler, C. & Kolling, S. (2022). Spannungsoptische Untersuchungen an polymeren Zwischenschichten in Verbundgläsern. 10.1002/cepa.1673
• Bulla, M., Schmandt, C., Kolling, S., Kisters, T. & Sahraei, E. (2022). An Experimental and Numerical Study on Charged 21700 Lithium-Ion Battery Cells under Dynamic and High Mechanical Loads. 10.3390/en16010211
• Chen, S., Kolling, S. & Kuntsche, J. (2022). Glass and Extreme Events. 10.1007/s40940-022-00216-7
• Memic, M., Pfister, J., Beckers, T., Lademann, F., Merkel, M., Jürgens, W. & Beitelschmidt, M. (2022). Forschungsprojekt VeRa: Verschleißreduzierung am Eisenbahnrad.
• Schrader, P., Schmandt, C. & Marzi, S. (2022). Mode I creep fracture of rubber-like adhesive joints at constant crack driving force. 10.1016/j.ijadhadh.2021.103079
• Schrader, P. & Marzi, S. (2022). Mode III testing of structural adhesive joints at elevated loading rates. 10.1016/j.ijadhadh.2021.103078

Konferenzpaper

• Brokmann, C., Alter, C. & Kolling, S. (2022). Stochastic Simulation of the Head Impact on Windscreens. https://www.scipedia.com/wd/images/e/ea/Draft_Sanchez_Pinedo_1093464641894_paper.pdf
• Ladwig, N., Domladovac, D. & Marzi, S. (2022). Fracture testing of adhesive joints in mixed-mode I+III. 10.1016/j.prostr.2022.12.082
• Bödeker, F., Herr, P., Moshfegh, R., Biel, A. & Marzi, S. (2022). A novel FFT-based homogenization scheme for cohesive zones. 10.1016/j.prostr.2022.12.062
• Herr, P., Bödeker, F. & Marzi, S. (2022). Numerical investigation on the effect of fillers on the fracture behavior of adhesives. 10.1016/j.prostr.2022.12.063
• Domladovac, D., Wolf, C., Kryukov, I., Kahlmeyer, M., Böhm, S. & Marzi, S. (2022). On the localisability of gaps in adhesive joints loaded in mode I. 10.1016/j.prostr.2022.12.048
• Dix, S., Thiele, K., Efferz, L., Schuler, C., Thiele, K., Schneider, J. & Kolling, S. (2022). Test facilities and concept for the evaluation of optical anisotropy effects in tempered glass.

Forschungsbericht

• Kolling, S., Pfeiffer, M., Moos, C. & Klass, K-D. (2022). BioDASH - Bionisch Dämpfender Automatik-Schutzhelm; Förderprogramm: Ideenwettbewerb Biologisierung der Technik. 10.2314/KXP:1887436235
• Lippold, C., Enzfelder, K., Bark, A. & Kutschera, R. (2022). Wirkung, Akzeptanz und Dauerhaftigkeit von Elementen der Fahrtrichtungstrennung auf Landstraßen. https://bast.opus.hbz-nrw.de/frontdoor/index/index/docId/2604

Wissenschaftliche Vortragsfolien

• Kolling, S., Brokmann, C. & Alter, C. (2022). Notes on Simulating Head Impact on Windshields. https://www.dynamore.de/en/training/conferences/past/16th-ls-dyna-forum-2022/dynaforum_glass_2022.pdf
• Moos, C., Pfeiffer, M., Kolling, S., Klass, K-D. & Plangger, U. (2022). Prototyping and Virtual Testing of Sports and Work Helmets. https://www.dynamore.de/en/training/conferences/past/16th-ls-dyna-forum-2022/045_moos_thm.pdf

2021

Journalartikel

• Brokmann, C., Kolling, S. & Schneider, J. (2021). Subcritical crack growth parameters in glass as a function of environmental conditions. 10.1007/s40940-020-00134-6
• Müller-Braun, S., Brokmann, C., Schneider, J. & Kolling, S. (2021). Strength of the individual glasses of curved, annealed and laminated glass used in automotive windscreens. 10.1016/j.engfailanal.2021.105281
• van Roo, T., Kolling, S., Dillenberger, F. B. & Amberg, J. (2021). On short glass fiber reinforced thermoplastics with high fiber orientation and the influence of surface roughness on mechanical parameters. 10.1177/07316844211051748
• Bulla, M., Kolling, S. & Sahraei, E. (2021). A Material Model for the Orthotropic and Viscous Behavior of Separators in Lithium-Ion Batteries under High Mechanical Loads. 10.3390/en14154585
• Berlinger, M., Kolling, S. & Schneider, J. (2021). A generalized Anderson–Darling test for the goodness-of-fit evaluation of the fracture strain distribution of acrylic glass. 10.1007/s40940-021-00149-7
• Dix, S., Müller, P., Schuler, C., Kolling, S. & Schneider, J. (2021). Digital image processing methods for the evaluation of optical anisotropy effects in tempered architectural glass using photoelastic measurements. 10.1007/s40940-020-00145-3
• Schmidt, A., Kididane, I., Schlenz, M. A., Wöstmann, B., Kolling, S. & Schrader, P. (2021). Finite element simulation of fixed dental prostheses made from PMMA —Part I: Experimental investigation under quasi-static loading and chewing velocities. 10.4012/dmj.2020-230
• Schrader, P., Kolling, S., Schlenz, M. A., Wöstmann, B. & Schmidt, A. (2021). Finite element simulation of fixed dental prostheses made from PMMA —Part II: Material modeling and nonlinear finite element analysis. 10.4012/dmj.2020-231
• Schmidt, A., Schrader, P., Frendel, K., Schlenz, M. A., Wöstmann, B. & Kolling, S. (2021). Is the assumption of linear elasticity within prosthodontics valid for polymers?. 10.4012/dmj.2019-373
• Kolling, S., Schneider, J., Schilling, R. & Gevers, M. (2021). Stochastic Simulation of the Fracture Behavior of Windshields in a Headform Impact. 10.1007/s38311-021-0694-6

Konferenzpaper

• Brokmann, C., Kolling, S. & Schneider, J. (2021). Subcritical Crack Growth Parameters for Glass under Different Environmental Conditions.
• Bayram, K., Pfeiffer, M., Alter, C. & Kolling, S. (2021). An Experimental and Numerical Investigation on Vulcanized Fiber. https://www.dynalook.com/conferences/13th-european-ls-dyna-conference-2021/testing-and-calibration/bayram_thm.pdf
• Jung, U., Hemmelmann, O. & Kern, A. (2021). Charakterisierung und Bewertung von defekten in additiv gefertigtem ALSI10MG hinsichtlich Werkstoffermüdung. 10.48447/Add-2021-009

Sammelbandbeitrag

• Sato, C. & Marzi, S. (2021). High-rate loading and impact in adhesively bonding joints. 10.1016/B978-0-12-819954-1.00015-0

Konferenzposter

• Schrader, P., Schmandt, C. & Marzi, S. (2021). Optical investigation of energy-controlled mode I crack propagation in viscoelastic adhesive joints.

2020

Journalartikel

• Bach, R., Götzinger, R., Kiziltoprak, N., Pfeiffer, M., Schabel, S., Schneider, J., Knaack, U. & Kolling, S. (2020). Warum … und nicht … ? Fragen, Gedanken und Diskussionen zum Bauen mit Papier.
• Bödeker, F. & Marzi, S. (2020). Applicability of the mixed-mode controlled double cantilever beam test and related evaluation methods. 10.1016/j.engfracmech.2020.107149
• Bulla, M., Kolling, S. & Sahraei, E. (2020). An Experimental and Computational Study on the Orthotropic Failure of Separators for Lithium-Ion Batteries. 10.3390/en13174399
• Drass, M., Du Bois, P. A., Schneider, J. & Kolling, S. (2020). Pseudo-elastic cavitation model: part I—finite element analyses on thin silicone adhesives in façades. 10.1007/s40940-019-00115-4
• Rühl, A., Kolling, S. & Schneider, J. (2020). A transparent three-layered laminate composed of poly(methyl methacrylate) and thermoplastic polyurethane subjected to low-velocity impact. 10.1016/j.ijimpeng.2019.103419
• Schrader, P., Gosch, A., Berer, M. & Marzi, S. (2020). Fracture of Thin-Walled Polyoxymethylene Bulk Specimens in Modes I and III. 10.3390/ma13225096

Monographie

• Groß, T. (2020). Technische Produktdokumentation. 10.1007/978-3-658-28267-7

Konferenzpaper

• Brokmann, C. & Kolling, S. (2020). A Model for the Stochastic Fracture Behavior of Glass. https://www.dynalook.com/conferences/16th-international-ls-dyna-conference/occupant-protection-t3-2/t3-2-c-occupant-protection-137.pdf
• Pfeiffer, M., Götzinger, R., Hiller, B., Kolling, S. & Schabel, S. (2020). Experimental and numerical investigation of single sheet out-of-plane compression tests of different paperboards.
• Tinz, J. & Fiedler, U. (2020). NC-Programming for Rolling Rotationally Asymmetrical Workpieces. 10.2507/31st.daaam.proceedings.106
• Hemmelmann, O., Jung, U., Barke, D. & Beier, H-T. (2020). Wirkung der Oberflächenbeschaffenheit auf die Schwingfestigkeit in der additiven Fertigung mit SLM für AlSi10Mg.

Sammelbandbeitrag

• Bark, A. (2020). Verhinderung von Baumunfällen durch Sicherheitsaudits von Straßen. https://www.dvr.de/fileadmin/downloads/dvr-schriftenreihe/Schriftenreihe-Verkehrssicherheit-22.pdf

2019

Journalartikel

• Brokmann, C., Berlinger, M., Schrader, P. & Kolling, S. (2019). Fraktographische Bruchspannungs-Analyse von Acrylglas. 10.1002/cepa.1013
• Brokmann, C., Alter, C. & Kolling, S. (2019). Experimental determination of failure strength in automotive windscreens using acoustic emission and fractography. 10.1007/s40940-018-0090-9
• Pfeiffer, M. & Kolling, S. (2019). A non-associative orthotropic plasticity model for paperboard under in-plane loading. 10.1016/j.ijsolstr.2019.02.012
• Fritz, S., Pfeiffer, M. A. & Gollnick, J. (2019). Optimierung der Austenitisierungszeit beim Presshärten von Stählen durch Anwendung des Hollomon-Jaffe Parameters. 10.1002/mawe.201700167
• Pfister, J., Lademann, F., Dückershoff, R., Memic, M., Berg, H. P. & Merkel, M. (2019). Simulatorbasiertes Training für ein besseres Situationsbewusstsein.

Konferenzpaper

• Peresada, S., Nikonenko, Y., Kovbasa, S., Kuznietsov, A. & Pushnitsyn, D. (2019). Rapid Prototyping Station for Batteries-Supercapacitors Hybrid Energy Storage Systems. 10.1109/ELNANO.2019.8783731
• Subke, J., Nalik, O., Pitzer, M. & Gollnick, J. (2019). Modellierung der Beanspruchung von Hüftendoprothesen im Knochen.

2018

Journalartikel

• Loh, L. & Marzi, S. (2018). Mixed-mode I+III tests on hyperelastic adhesive joints at prescribed mode-mixity. 10.1016/j.ijadhadh.2018.05.024
• Drass, M., Schneider, J. & Kolling, S. (2018). Damage effects of adhesives in modern glass façades: a micro-mechanically motivated volumetric damage model for poro-hyperelastic materials. 10.1007/s10999-017-9392-3
• Koerver, R., Zhang, W., de Biasi, L., Schweidler, S., Kondrakov, A. O., Kolling, S., Brezesinskic, T., Hartmann, P., Zeier, W. G. & Janek, J. (2018). Chemo-mechanical expansion of lithium electrode materials – on the route to mechanically optimized all-solid-state batteries. 10.1039/C8EE00907D
• Drass, M., Schwind, G., Schneider, J. & Kolling, S. (2018). Adhesive connections in glass structures—part II: material parameter identification on thin structural silicone. 10.1007/s40940-017-0048-3
• Drass, M., Schwind, G., Schneider, J. & Kolling, S. (2018). Adhesive connections in glass structures—part I: experiments and analytics on thin structural silicone. 10.1007/s40940-017-0046-5
• Drass, M., Kolupaev, V. A., Schneider, J. & Kolling, S. (2018). On cavitation in transparent structural silicone adhesive: TSSA. 10.1007/s40940-018-0061-1
• Drass, M., Schneider, J. & Kolling, S. (2018). Novel volumetric Helmholtz free energy function accounting for isotropic cavitation at finite strains. 10.1016/j.matdes.2017.10.059
• Loh, L. & Marzi, S. (2018). An Out-of-plane Loaded Double Cantilever Beam (ODCB) test to measure the critical energy release rate in mode III of adhesive joints. 10.1016/j.ijadhadh.2018.02.021
• Schmandt, C. & Marzi, S. (2018). Effect of crack opening velocity and adhesive layer thickness on the fracture behaviour of hyperelastic adhesive joints subjected to mode I loading. 10.1016/j.ijadhadh.2018.02.028

Monographie

• Baier, R., Baier, M. M., Klemps-Kohnen, A., Bark, A., Chales-de Beaulieu, C. & Theis, C. (2018). Evaluation des Sicherheitsaudits von Straßen in der Planung. https://edocs.tib.eu/files/e01fn18/1038709520.pdf
• Haldor, J. & Lademann, F. (2018). Planung von Bahnanlagen.

Konferenzpaper

• Brokmann, C. & Kolling, S. (2018). Comparison of Failure Stress Distributions in Automotive Windscreens by Experiment and Simulation. https://www.dynamore.it/de/fortbildung/konferenzen/vergangene/2018-ls-dyna-forum/agenda/e-10-pedestrian-safety-brokmann-thmittelhessen.pdf
• Loh, L. & Marzi, S. (2018). A Mixed-Mode Controlled DCB test on adhesive joints loaded in a combination of modes I and III. 10.1016/j.prostr.2018.12.277
• Pfeiffer, M., Kolling, S., Stein, P. & Franke, W. (2018). A modified in-plane constitutive model for paperboard. https://www.dynamore.de/de/fortbildung/konferenzen/vergangene/2018-ls-dyna-forum/agenda/f-12-orthotropic-plasticity-damage-failure-pfeiffer-thmittelhessen.pdf
• Schmandt, C. & Marzi, S. (2018). Effect of crack opening velocity on fracture behavior of hyperelastic semi-structural adhesive joints subjected to mode I loading. 10.1016/j.prostr.2018.12.154

Konferenzposter

• Alter, C., Kolling, S. & Schneider, J. (2018). An enhanced non-local failure criterion for laminated glass under low velocity impact.

2017

Journalartikel

• Kaskah, S. E., Pfeiffer, M., Klock, H., Bergen, H., Ehrenhaft, G., Ferreira, P., Gollnick, J. & Fischer, C. B. (2017). Surface protection of low carbon steel with N-acyl sarcosine derivatives as green corrosion inhibitors. 10.1016/j.surfin.2017.08.002
• Alter, C., Kolling, S. & Schneider, J. (2017). An enhanced non–local failure criterion for laminated glass under low velocity impact. 10.1016/j.ijimpeng.2017.07.014
• Rühl, A., Kolling, S. & Schneider, J. (2017). Characterization and modeling of poly(methyl methacrylate) and thermoplastic polyurethane for the application in laminated setups. 10.1016/j.mechmat.2017.07.018
• Mattiello, S., Kolling, S. & Heiliger, C. (2017). Kinetic Monte Carlo simulations of fluorine and vacancies concentration at the CeO2 (111) surface. 10.1088/1361-651X/aa763d
• Kaiser, B., Pyttel, T., Haug, E. & Duddeck, F. (2017). Draping simulation with a new finite element formulation involving an internal unit cell. 10.1063/1.5007988

Monographie

• Bark, A., Kutschera, R., Resnikow, K., Follmann, J. & Biederbick, M. (2017). Werkzeuge zur Durchführung von Bestandsaudits und thematischen Sonderuntersuchungen.
• Bark, A., Krähling, D., Kutschera, R., Baier, M., Baier, R., Klemps-Kohnen, A., Schuckließ, L., Maier, R. & Berger, R. (2017). Bewertungsmodelle für die Verkehrsssicherheit von Autobahnen und von Landstraßenknotenpunkten.

Konferenzpaper

• Kuznietsov, A. & Happek, T. (2017). On-board diagnostics of Li-Ion battery packs for electric vehicles using a combination of spectroscopy and identification methods. 10.1109/UKRCON.2017.8100314
• Kiselev, A., Kuznietsov, A. & Leidhold, R. (2017). Model based online detection of inter-turn short circuit faults in PMSM drives under non-stationary conditions. 10.1109/CPE.2017.7915199
• Wörner, S., Jung, U., Friederich, H., Beier, T. & Vormwald, M. (2017). Additive manufactured components for mechanical engineering and automotive industry.
• Rühl, A., Kolling, S., Schneider, J. & Kiesewetter, B. (2017). Laminated amorphous polymers subjected to low-velocity impact. https://www.dynamore.de/en/downloads/flyer/2017/european-ls-dyna-conference-book-of-abstracts
• Sygusch, N., Lauterbach, B., Ruesch, N., Kolling, S. & Schneider, J. (2017). Stochastic approach to rupture probability of short fiber reinforced polypropylene for automotive crash applications. https://www.dynamore.de/en/downloads/flyer/2017/european-ls-dyna-conference-book-of-abstracts
• Alter, C., Kolling, S. & Schneider, J. (2017). A new failure Criterion for laminated safety glass. https://www.dynamore.de/en/downloads/flyer/2017/european-ls-dyna-conference-book-of-abstracts

Sammelbandbeitrag

• Zima, S., Breuer, C. & Schäfer, F. (2017). Triebwerk. 10.1007/978-3-658-10902-8_6
• Breuer, C. & Zima, S. (2017). Geschichtlicher Rückblick. 10.1007/978-3-658-10902-8_1
• Breuer, C. & Brillert, H-R. (2017). Kolbenringe. 10.1007/978-3-658-10902-8_7
• Breuer, C. & Robota, A. (2017). Zylinder. 10.1007/978-3-658-10902-8_7
• Breuer, C. (2017). Drehschwingungen. 10.1007/978-3-658-10902-8_6
• Wörner, S., Jung, U., Friederich, H., Beier, H. & Vormwald, M. (2017). Rapid Prototyping im Maschinen- und Automobilbau. 10.1007/978-3-658-17780-5_1

Wissenschaftliche Vortragsfolien

• Roth, M., Kolling, S., Thomas, D. & Kellner, G. (2017). Modellierung von glasfaserverstärkten Duroplasten zum Einsatz in ballistischen Schutzaufbauten. https://www.technologydays.at/prepdfs/tt2017/TT17_t2_a06.pdf

2016

Journalartikel

• Gloeckner, R., Kolling, S. & Heiliger, C. (2016). A Monte-Carlo Algorithm for 3D Fibre Detection from Microcomputer Tomography. 10.1155/2016/2753187
• Rühl, A., Kolling, S., Mende, V. & Kiesewetter, B. (2016). Computational design of a heated PMMA window validated by infrared thermography. 10.1007/s40940-016-0004-7
• Mattiello, S., Kolling, S. & Heiliger, C. (2016). Surface vacancies concentration of CeO2(1 1 1) using kinetic Monte Carlo simulations. 10.1088/0965-0393/24/1/015011
• Lademann, F. & Menius, R. (2016). Pragmatische Fahrzeitverbesserungen zwischen Bayern und Tschechien – Teil 1.
• Lademann, F. & Menius, R. (2016). Pragmatische Fahrzeitverbesserungen zwischen Bayern und Tschechien – Teil 2.

Konferenzpaper

• Menz, P., Baumgaertner, F., Fiedler, U. & Bergmann, G. (2016). Improvement of Green Machining Through the Use of Design of Experiments.
• Fiedler, U., Bergmann, G., Abt, C., Baumgärtner, F. & Menz, P. (2016). Optimierung der spanenden Bearbeitung von Grünteilen mittels statistischer Versuchsplanung.

2015

Journalartikel

• Müller, V., Brylka, B., Dillenberger, F., Glöckner, R., Kolling, S. & Böhlke, T. (2015). Homogenization of elastic properties of short-fiber reinforced composites based on measured microstructure data. 10.1177/0021998315574314

Monographie

• Bark, A., Kutschera, R., Resnikow, K., Baier, M. M. & Schuckließ, W. (2015). Entwurfstechnische Empfehlungen für Autobahntunnelstrecken. https://bast.opus.hbz-nrw.de/files/1544/V265_barrierefreies_ELBA_PDF.pdf

Konferenzpaper

• Manthei, G., Alter, C. & Kolling, S. (2015). Localization of Initial Cracks in Laminated Glass Using Acoustic Emission Analysis – Part I. https://www.ndt.net/search/docs.php3?id=17573
• Sikora, S. P., Meschut, G. & Kolling, S. (2015). Material Characterization and Modeling for the Simulation of Adhesive Joints with Polyurethane Adhesives. https://www.nafems.org/publications/resource_center/nwc15_288/?srsltid=AfmBOoq_CmzetxAYYHb0MTIrCABxAQLwonn_ZIw6Fs3y7uEWTIg1qFBL

Sammelbandbeitrag

• Alter, C., Manthei, G., Kolling, S. & Schneider, J. (2015). Lokalisierung des initialen Versagens bei Verbundsicherheitsglas unter stoßartiger Belastung.

Forschungsbericht

• Kolling, S., Alter, C. & Rühl, A. (2015). Experimentelle und numerische Untersuchungen von Windschutzscheiben unter stoßartiger Belastung zur Verbesserung des Fußgänger- und Insassenschutzes. 10.2314/GBV:858609622

2013

Journalartikel

• Müller, V., Böhlke, T., Dillenberger, F. & Kolling, S. (2013). Homogenization of Elastic Properties of Short Fiber Reinforced Composites Based on Discrete Microstructure Data. 10.1002/pamm.201310130

Konferenzpaper

• Reppin, D., Kuhl, F., Piechotka, M., Henning, T., Klar, P. J., Wolf, N., Kolling, S. & Janek, J. (2013). Concepts for micro-thrusters based on solid state ion conductors : IEPC-2013-128. https://electricrocket.org/IEPC/2r262eiq.pdf
• Müller, V., Dillenberger, F., Brylka, B., Böhlke, T., Glöckner, R. & Kolling, S. (2013). Homogenization of elastic properties of short fiber reinforced composites based on micro computed tomography data. 10.5281/zenodo.15441408

Arbeitspapier

• Kolling, S. & Steinhilber, H. (2013). Technische Schwingungslehre. https://www.thm.de/me/images/user/kolling-94/schwingungslehre/Schwingungen.pdf

2012

Journalartikel

• Kolling, S., Larcher, M., Schneider, J., Alter, C., Gebbeken, N. & Kuntsche, J. (2012). Deformations- und Bruchverhalten von Verbundsicherheitsglas unter dynamischer Beanspruchung. 10.1002/stab.201201536

Konferenzpaper

• Schneider, J., Kolling, S., Kuntsche, J. & Moennich, S. (2012). Tensile properties of different polymer interlayers under high strain rates. https://www.researchgate.net/publication/283924146_Tensile_properties_of_different_polymer_interlayers_under_high_strain_rates

Wissenschaftliche Vortragsfolien

• Strauch, J., Altenbach, H., Kolling, S. & Becker, F. (2012). Simulation kurzzeitdynamischer Vorgänge unter Berücksichtigung thermomechanischer Effekte in der Materialmodellierung von Polyamid6. https://www.technologydays.at/prepdfs/tt2012/TT12_s5v2_Strauch.pdf

2010

Journalartikel

• Bark, A. & Schmidt, H. (2010). Entwicklung eines dreidimensionalen Simulationstools zur Überprüfung von Straßenentwürfen auf sicherheitsrelevante Entwurfsdefizite für Sicherheitsauditoren und Planer von Landstraßen.

Monographie

• Bark, A., Kutschera, R., Baier, R. & Klemps-Kohnen, A. (2010). Sicherheitsrelevante Aspekte der Straßenplanung. https://bast.opus.hbz-nrw.de/files/371/V196.pdf

2009

Konferenzpaper

• Bark, A. (2009). Das Sicherheitsaudit von Straßen - Erfahrungen und Perspektiven.

2001

Journalartikel

• Bark, A. (2001). Sicherheitsaudit für Straßen in Deutschland - Planungsstand und Perspektiven.